Zynq-7000 SoC

XC7Z020-3CLG400E Field Programmable Gate Array FPGA Embedded Processors And Controller Chip

Applications

• Automotive driver assistance, driver information, and infotainment
• Broadcast camera
• Industrial motor control, industrial networking, and machine vision
• IP and Smart camera
• LTE radio and baseband
• Medical diagnostics and imaging
• Multifunction printers

• Video and night vision equipment

Specifications

Description

Zynq-7000 SoC First Generation Architecture

The Zynq®-7000 family is based on the Xilinx SoC architecture. These products integrate a feature-rich dual-core or single-core ARM® Cortex™-A9 based processing system (PS) and 28 nm Xilinx programmable logic (PL) in a single device. The ARM Cortex-A9 CPUs are the heart of the PS and also include on-chip memory, external memory interfaces, and a rich set of peripheral connectivity interfaces.

Features

ARM Cortex-A9 Based

Application Processor Unit (APU)

• 2.5 DMIPS/MHz per CPU

• CPU frequency: Up to 1 GHz

• Coherent multiprocessor support

• ARMv7-A architecture

• TrustZone® security

• Thumb®-2 instruction set

• Jazelle® RCT execution Environment Architecture

• NEON™ media-processing engine

• Single and double precision Vector Floating Point Unit (VFPU)

• CoreSight™ and Program Trace Macrocell (PTM)

• Timer and Interrupts

• Three watchdog timers

• One global timer

• Two triple-timer counters

On-Chip Memory

• On-chip boot ROM

• 256 KB on-chip RAM (OCM)

• Byte-parity support

External Memory Interfaces

• Multiprotocol dynamic memory controller

• 16-bit or 32-bit interfaces to DDR3, DDR3L, DDR2, or LPDDR2 memories

• ECC support in 16-bit mode

• 1GB of address space using single rank of 8-, 16-, or 32-bit-wide memories

• Static memory interfaces

• 8-bit SRAM data bus with up to 64 MB support

• Parallel NOR flash support

• ONFI1.0 NAND flash support (1-bit ECC)

• 1-bit SPI, 2-bit SPI, 4-bit SPI (quad-SPI), or two quad-SPI (8-bit) serial NOR flash

8-Channel DMA Controller

• Memory-to-memory, memory-to-peripheral, peripheral-to-memory, and scatter-gather transaction support

I/O Peripherals and Interfaces

• Two 10/100/1000 tri-speed Ethernet MAC peripherals with IEEE Std 802.3 and IEEE Std 1588 revision 2.0 support

• Scatter-gather DMA capability • Recognition of 1588 rev. 2 PTP frames

• GMII, RGMII, and SGMII interfaces

• Two USB 2.0 OTG peripherals, each supporting up to 12 Endpoints

• USB 2.0 compliant device IP core

• Supports on-the-go, high-speed, full-speed, and low-speed modes

• Intel EHCI compliant USB host

• 8-bit ULPI external PHY interface

• Two full CAN 2.0B compliant CAN bus interfaces

• CAN 2.0-A and CAN 2.0-B and ISO 118981-1 standard compliant

• External PHY interface

• Two SD/SDIO 2.0/MMC3.31 compliant controllers

• Two full-duplex SPI ports with three peripheral chip selects

• Two high-speed UARTs (up to 1 Mb/s)

• Two master and slave I2C interfaces

• GPIO with four 32-bit banks, of which up to 54 bits can be used with the PS I/O (one bank of 32b and one bank of 22b) and up to 64 bits (up to two banks of 32b) connected to the Programmable Logic

• Up to 54 flexible multiplexed I/O (MIO) for peripheral pin assignments

Interconnect

• High-bandwidth connectivity within PS and between PS and PL

• ARM AMBA® AXI based

• QoS support on critical masters for latency and bandwidth control

Trading Guide

Shenzhen Retechip® Electronic Technology Co., Ltd. was established in 2013, specializing in electronic components distribution business.The products are widely used in communication equipment, power supply, medical electronics, automotive electronics, digital electronics, industrial electronics, display modules, intelligent electronics, new energy, the Internet of things, 5G productsand other fields，With high-quality products, reasonable prices, rapid distributionand timely service, we can provide customers with the most cost-effective products and save customers a lot of time.